Joiner's works Joiner's works in rural mestosti Works of the joiner Work of the joiner in a countryside

Stools and tables

 
 

Stools, the most simple, but at the same time and easy carry out the strong on nails (fig. 115, and. Stools, or easy small benches, produce so. Take a wide board or narrow, but they then should be forced down till the necessary width. All plane. Then produce legs with corresponding cuts for tsarg. TSargi are boards not already 150 mm, which krepjat to legs nails, a seat - also the nails which are driven in into legs and tsargi.

Easy little tables and stools can be made in another way. At first do a seat or a cover of boards or boards of the necessary form and the size. To the bottom party of a seat krepjat tsargi triangular, square or squared or brought down from two boards. Boards for tsarg take in the thickness of 30-50 mm that legs more strongly kept. In tsargah drill or hollow apertures in diameter of 25-30 mm or square the same section. Then tsargi krepjat to a seat nails or glue and nails. After that produce legs of the square, rectangular or round form with necks of such size that they with sufficient effort entered into apertures or nests tsarg. Legs can be put dry, but it is desirable on glue (fig. 115.

Stools and little tables on nails: and - without rasporki; - with rasporkoj; in - easy little tables and stools

115. Stools and little tables on nails :
And - without rasporki; - with rasporkoj; in - easy little tables and stools

The Stool on glue and joiner's connections (fig. 116) consists of four legs, four tsarg, four prolegs, crackers and a seat.

The Stool produce in such sequence. Plane boards, spend risks.

In legs for tsarg and prolegs hollow deep nests, in tsargah - nests for crackers depth to 150 mm. On the ends tsarg and prolegs zapilivajut thorns. Legs produce section 45x45 mm from bruskov in the length 460 mm.

Tsargi, prolegs, a seat and crackers produce from boards in the thickness of 25 mm. Length tsarg - 305 mm, and width - 67 mm; length of prolegs - of 305 mm, width - 31 mm.

the Stool on glue: and - a general view; - a skeleton without a seat; in - tsarga and a proleg; g - the top view; d - check of pairs legs; g - a seat; - the basic connections tsarg with legs

116. A stool on glue :
And - a general view; - a skeleton without a seat; in - tsarga and a proleg; g - the top view; d - check of pairs legs; g - a seat; - the basic connections tsarg with legs

The Seat do of five - seven boards in the thickness of 25 mm and width on-80 mm, length on 385 mm. Crackers carry out in the length and in the width on 70 mm.

For maintenance of durability and rigidity of a stool the ends of thorns tsarg and prolegs cut off at an angle 45° that they in nests have converged closely. The bottom ends of legs from two parties ostragivajut on a cone with section below 28x28 mm.

Stool Details should incorporate without backlashes. After adjustment of all details collect steams or stool halves at first dry, then - on glue, it is strict in a square and without warps.

Collected steams connect by means of remained two tsarg and two prolegs, forming the case, at first dry, and after check - on glue.

Separate boards of a seat collect on glue and round or flat shkantah. After board drying plane till the thickness of 20 mm, cutting off on the size. Acute angles slightly round off.

Then in a proper place of a seat from its back party drill for shkantov two round apertures depth of 10-12 mm. The seat should be put on on shkanty with some effort. After that krepjat crackers which insert thorns into nests in tsargah and krepjat to a seat screws. After that cut off (straighten) legs. That wood was not chopped off from a bottom of legs, from them remove a small facet.

The Basic connections of a skeleton and stool manufacturing are shown in drawing 116.